The correct use of MY40 megohmmeter Guangzhou Chengmin Electronic Technology Co., Ltd. professional advantage to supply imported domestic brands megohmmeter, insulation resistance tester, shaker, grounding resistance meter! A large number of spot advantages supply! Welcome to inquire and purchase!
The correct measurement method of insulation resistance:
Modern life is changing with each passing day, and people can't live without electricity for a moment. There are electrical safety issues in the process of electricity use, in electrical equipment, such as motors, cables, household appliances, and so on. One of their normal operations is the degree of insulation of the insulating material, ie the value of the insulation resistance. When heated and damp, the insulation ages. Its insulation resistance is reduced. This causes electrical equipment leakage or short-circuit accidents. In order to avoid accidents, it is required to constantly measure the insulation resistance of various electrical equipment. Determine if the insulation level meets the needs of the equipment. Common resistance measurements are usually measured at low voltage and at high voltage. The insulation resistance is higher due to the general value (generally megaohms). Measurements at low voltages do not reflect true insulation resistance values ​​operating at high voltages. The megohmmeter is also called an insulation resistance meter. It is the most commonly used meter for measuring insulation resistance. It has a high-voltage power supply when measuring the insulation resistance, which is the difference between it and the resistance meter. The megohmmeter is convenient and reliable for measuring insulation resistance. However, if it is used improperly, it will bring unnecessary errors to the measurement. We must use the megohmmeter insulation resistance for measurement.
When the megohmmeter is working, it generates high voltage itself, and the measuring object is electrical equipment, so it must be used correctly, otherwise it will cause personal or equipment accidents. Before using, you must first make the following preparations:
(1) Before the measurement, the power of the device under test must be cut off, and the ground should be short-circuited. The device must not be energized for measurement to ensure the safety of the person and equipment.
(2) For equipment that may induce high voltage, the possibility must be eliminated before measurement can be made.
(3) The surface of the object to be tested should be cleaned to reduce the contact resistance and ensure the correctness of the measurement results.
(4) Before the measurement, check whether the megohmmeter is in normal working condition, mainly check the two points of “0†and “∞â€. That is, the handle is shaken to make the motor reach the rated speed. The megger should be in the “0†position when it is short-circuited and “∞†when it is open.
(5) The megohmmeter should be placed in a stable and stable place and away from large external current conductors and external magnetic fields.
After the above preparations are made, the measurement can be carried out. When measuring, pay attention to the correct wiring of the megohmmeter, otherwise it will cause unnecessary errors or even errors.
There are three terminals of the megohmmeter: one is “Lâ€, that is, the line end, one “E†is the ground end, and another “G†is the shield end (also called the protection ring). Generally, the insulation resistances to be tested are connected. Between the "L" and "E" ends, but when the surface of the insulator to be tested is seriously leaky, the shield ring of the test object or the portion not to be measured must be connected to the "G" end. Thus, the leakage current flows directly back to the negative end of the generator via the shield end "G" to form a loop, rather than flowing through the megohmmeter measuring mechanism (moving coil). This fundamentally eliminates the influence of surface leakage current. In particular, it should be noted that when measuring the insulation resistance between the cable core and the outer surface, the shield terminal "G" must be connected because the air humidity is high or the cable is insulated. When the surface is not clean, the leakage current on the surface will be very large. In order to prevent the measured object from being affected by leakage, its internal insulation measurement is generally added to the outer surface of the cable with a metal shielding ring, and the megger of the megohmmeter. "End connected.
When using the megohmmeter to measure the insulation resistance of electrical equipment, be sure to note that the "L" and "E" ends cannot be reversed. The correct connection is: "L" line end button is connected to the conductor of the device under test, "E" The grounding device is grounded, and the “G†shield terminates the insulated part of the device under test. If the "L" and "E" are reversed, the leakage current flowing through the insulator and the surface is collected to the ground through the outer casing, and the ground flows through the "L" into the measuring coil, so that the "G" loses the shielding effect and gives the measuring tape. There is a big error. In addition, because the inner lead of the "E" end is insulated from the outer casing by a degree of insulation lower than the "L" end and the outer casing, when the megohmmeter is placed on the ground, when the correct wiring is used, the "E" end is opposite to the outer casing of the instrument. The insulation resistance of the shell to the ground is equivalent to a short circuit and does not cause an error. When the "L" and the "E" are reversed, the insulation resistance of the "E" to the ground is in parallel with the measured insulation resistance, and the measurement result is biased. Small, causing large errors in the measurement.
It can be seen that in order to accurately measure the insulation resistance of electrical equipment, etc., the megohmmeter must be used correctly, otherwise the accuracy and reliability of the measurement will be lost.
Japan Yokogawa YOKOGAWA full range of insulation resistance tester:
MY40-01, MY10-01, MY10-02, MY10-03, MY10-04, MY10-05, 3213A41, 3213A42, 3213A43, 3213A44, 3213A45, 2406E31, 2406E41, 2406E32, 2406E42, 2406E33, 2406E43, 2406E34, 2406E44, 2406E35, 2406E45
Japan Hioki full range of insulation resistance tester:
IR4016-20, IR4017-20, IR4018-20, IR4057-20, IR4056-20, 3455-20, 3490, 3151, FT6380
Shanghai Sixth Factory, Shanghai Kanghai, Beijing Far East, Hangzhou Chaoyang, Hangzhou Dongshun, Nanjing Jinchuan, Zhengda and other domestic megohmmeter/shake table specifications:
ZC25-1 100V 100MΩ
ZC25-2 250V 250MΩ
ZC25-3 500V 500MΩ
ZC25-4 1000V 1000MΩ
ZC25B-1 100V 100MΩ
ZC25B-2 250V 250MΩ
ZC25B-3 500V 500MΩ
ZC25B-4 1000V~1000MΩ
ZC-7-1 500V~1000MΩ
ZC-7-2 1000V~2000MΩ
ZC-7-3 2500V~5000MΩ
ZC-7-4 5000V~10000MΩ
ZC8-1 0-1-10-100Ω
ZC8-2 0-1-10-100-1000Ω
ZC11D-1 100V 500 MΩ
ZC11D-2 250V 1000 MΩ
ZC11D-3 500V 2000 MΩ
ZC11D-4 1000V 5000 MΩ
ZC11D-5 2500V 10000 MΩ
ZC11D-6 100V 20 MΩ
ZC11D-7 250V 50 MΩ
ZC11D-8 500V 100 MΩ
ZC11D-9 50V 200 MΩ
ZC11D-10 2500V 2500 MΩ
ZC-18 0-1-10-100 (explosion-proof type)
ZC29B-1 0-1-10-100-1000Ω
ZC29B-2 0-1-10-100Ω
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
A mudflap or mud guard is used in combination with the vehicle fender to protect the vehicle, passengers, other vehicles, and pedestrians from mud and other flying debris thrown into the air by the rotating tire. A mudflap is typically made from a flexible material such as rubber that is not easily damaged by contact with flying debris, the tire, or the road surface.
Mudflaps can be large rectangular sheets suspended behind the tires, or may be small molded lips below the rear of the vehicle's wheel wells. Mudflaps can be aerodynamically engineered, utilizing shaping, louvers or vents to improve airflow and lower drag.
custom molded Mud Guards are made from durable, rubber that's as tough as nails (or rocks for that matter). With a growing number of "No Drilling Required" applications, they're easy to install, conform perfectly to your fenders, and protect your ride and those around you from the rage of the road. Let them splash guards do the work.
Company information:
RenqiuXingcheng Rubber Products Co., Ltd. is located in the side of the Baiyang lake, our company is professional manufacturer of rubber products. We are one of the leading rubber company in china,The company is a private enterprise which is engaged in scientific research, production, sales and service and has obtained ISO 9001 certification. Our main business is producing all kinds of rubber products, including anti-skid plates, Rubber Sheet Series, Rubber Mat Series and horse mat series ect., The products are shockproof, anti-wear, anti-high and low temperature, anti-aging, oil resistant and chemical resistant in character.At present, our products have been sold at home and abroad and mainly exported to Canada, Germany, Chile, etc. We welcome domestic and foreign merchants to negotiate and cooperate with us. We are willing to join hands with old and new friends in creating a better tomorrow.
Rubber Mud Flap,Heavy Duty Rubber Mud Flaps,Rubber Mud Flap For Trailer,Truck Rubber Mud Flaps
Renqiu Xingcheng Rubber Products Co., Ltd. , https://www.rubbermats.nl