How to use the linear vibrating screen Linear vibrating screen Compared to the rotary vibrating screen, a little more attention should be paid. The linear vibrating screen has two kinds of wooden and steel meshes, and the wooden mesh screen can be changed easily, but the wooden mesh The rack is easily broken, so check it often. The output of the linear vibrating screen is large, so the loss of the screen and the loss of the bouncing ball are also relatively large and also need to be checked frequently. Second, the linear vibrating screen is the use of two vibration motors, the excitation force is relatively large, so the angle of the motor eccentric block must be adjusted, and the motor should often be filled with butter to lubricate the bearing. If the motor is to be repaired or replaced in time after its service life, the selected motor must be of the same type. If the motor model is inconsistent, there will be problems such as non-discharging, abnormal material movement trajectory, and even cracking of the screen.
The use of ultrasonic vibrating screens The operating rules of ultrasonic vibrating screens are a bit more complicated. This involves the maintenance and maintenance of ultrasonic power supplies and ultrasonic transducers. The ultrasonic power supply must be placed in a place where the dust is relatively small and away from other electronic devices. interference. Ultrasonic transducers must be tightened during installation to prevent materials from entering the interior. Some materials may conduct electricity or generate static electricity. If they enter the transducer, they will short-circuit and burn together. This must be noted, I noticed that there are many The customer is because of this problem, resulting in continuous problems with ultrasonic vibrating screens, affecting production use. In addition, the mechanical wave generated by the ultrasonic vibrating screen makes the screen vibration frequency is very high to achieve the material does not block the network, so the period of the screen break is very short, so when using it must always check the screen for damage, and timely Use tooling replacement. Note: When the tooling is the ultrasonic vibration screen given by the company to the customer, if the customer request can add a set of screen-changing tools, it will be easier to replace the screen.
The use of rotary vibrating screens Before using rotary vibrating screens, the material test machine is first used. Normal screening production can be performed without problems. Then, at regular intervals, it is necessary to check whether the screen is damaged or not. Replace the screen to avoid delays in production. Second, the vibrating motor should be filled with butter at regular intervals to prevent the vibrating motor from being seriously worn and burned. Third, check whether the beam ring bolts of the screening machine are loose, and tighten them in time to avoid leakage of the screening machine. In addition, there must be no rigid objects next to the screen so as not to scratch the surface of the screen. The vibrating screen rubber strips and bouncing balls are also wearing parts. Consumables should be checked in a timely manner to see if there is any damage to the rubber. Replace them in time to avoid leakage and mixing.
The above vibrating screen technology, I hope the user to read it carefully when used, understand these matters to be noted, extend the life of the screen machine.
phone
Full round carbon tubes are created by wrapping resin pre-impregnated cloth strips around a mandrel and then curing the tube. The result is a highly specific and customizable tube that is lightweight and strong. 3K twill matte pure carbon fiber tubes are hot sellers.But 1.5K etc Full Carbon Fiber Tubes are available as well. These tubes can be cut,drilled holes,slotted,and have an variety of lengths and thicknesses. Our stocked wrapped carbon tubes are straight and octagonal 3K twill matte pure carbon fiber pipes which are frequently used in kiting, RC hobbies and so on.
For assembly perfectly, we could offer aluminum clampes. Generally speacking, they are made of 6061-T6 aluminum material. If you need other materials, they are available as well. Materials, shape dimension are based on your requirements.
If you don`t find the carbon fiber tubes and clamps you required in our catalog, please send us an RFQ with your specificationns. We could produce or customize them to fulfill your unique needs. According to your drawing we could offer a whole set Carbon Fiber Tube And Clamp.
Carbon Fiber Tube And Clamp
Carbon Fiber Tube Clamp,Carbon Fiber Pole,Carbon Fiber Telescopic Tube,Telescoping Carbon Fiber Tubes
Hobby Carbon CNC Technology(Shenzhen) Limited , https://www.hobbycarbon.com