According to the requirements of national laws and regulations on production safety, combined with occupational diseases existing in the construction industry, this measure is specifically formulated.
First, dust prevention measures
1. The comprehensive measures taken to prevent dust poisoning are: strengthen personal protection; reduce the concentration of toxic substances; eliminate toxic substances; strengthen safety and health management;
2, reform the production process and operating level, reduce the source of poisons.
3. Closed measures shall be taken for production equipment for dust and toxic substances to prevent running, running, dripping or leaking and reduce environmental pollution. Dust collectors and purifiers are used for purification.
4, install ventilation equipment, strengthen air refresh. Temporary construction site operations should be set up in a well-ventilated environment.
5. Observe personal hygiene and personal protection regulations. Wear work clothes, rubber boots, gloves, and masks as required.
6. Conduct regular medical examinations on the type of dust exposure.
Second, anti-virus technology measures
1. Measures taken by management and production departments in the prevention of occupational poisoning:
1) Strengthen management, do a good job in anti-virus work, and strictly enforce labor protection laws and hygiene standards.
2) Rely on science and technology to improve the technical level of prevention of poisoning. Reform process; prohibit the use of chemical products that are seriously hazardous; strengthen ventilation.
2. Measures taken by production workers to prevent occupational poisoning:
1) Conscientiously implement the operating procedures, master the operating methods, and prevent erroneous operations.
2) Wear personal protective equipment.
3, technical measures to prevent manganese poisoning:
1) Ventilation of welding workplaces is good so that the concentration of manganese fumes in the air is reduced to less than 0.2‰mg/m.
2) Try to adopt low-dust and low-toxicity welding rods and use automatic welding instead of manual welding.
3) Wear gloves and masks at work; do not eat or drink water in the workshop.
4, to prevent benzene poisoning measures:
1) Workers who use paint and spray paint should take comprehensive measures before construction. When entering a confined place, such as a basement or an oil tank, wear a gas mask.
2) The paint and furnishing room on the construction site should improve the natural ventilation conditions, reduce the continuous batching time, and prevent benzene poisoning.
5, to prevent the arc cursor radiation measures:
1) When working in the welding industry, masks equipped with protective lenses must be used. The lenses are selected based on the current intensity at the time of welding and the individual's eyes.
2) In order to prevent skin burns, welders must wear work clothes, gloves, and shoe covers.
Third, heatstroke cooling measures:
1. During the construction of high-temperature season, heat prevention and cooling should be done in accordance with labor protection regulations.
2. Conduct a health check on workers who have been exposed to high temperatures before going into the heat, and it is not advisable to engage in patients suffering from high-temperature diseases. Seasonal work should be properly exchanged.
3, open-air operations and high-temperature types of work in accordance with the nature of the work of a reasonable adjustment of time, take the morning class, late to close the work, to extend the lunch break time schedule, to ensure that employees can fully rest and work energetic.
4. The worksite with long construction period and no fixed resting place can use temporary materials such as temporary shelters.
5, high temperature workers, should be timely supply of tea or salt, sugar drinks.
6, physical examination should be carried out on high temperature workers, who have cardiovascular disease can not engage in high temperature operations. During the hot season, medical staff went to the scene to visit medical facilities and found that the heat stroke was saved in time.
Copyright statement: This article is a reprint of the online media, and it only represents the author's point of view. It has nothing to do with the China Labor Insurance Network. If news articles and comments infringe your legal rights, please call us and we will handle it in a timely manner.
Everyone knows how important the fill is to a Cooling Tower`s performance. Since fill is the heat transfer medium around which the [box" that is the cooling tower is built, you could argue that it`s the most important factor in determining just how well your cooling tower performs. However, since the nozzles are tasked with getting the hot water that you want to cool delivered to the fill, the nozzles also play a very important part in the duty of a tower. Nozzles are involved in the following aspects of a cooling tower`s performance evaluation.
The Advantages of Cooling tower nozzles:
1) Nozzles are grommeted for easy inspection and removal;
2) Multiple sizes are available to accommodate all system flow rates;
3) Large orifice mearns non-clogging performace for effective wetting of the heat-transfer surface.
Cooling Tower Nozzles,Marley Cooling Tower ,Cooling Tower Parts ,Marley Cooling Tower Parts
Shandong Hiking International Commerce Group Co.,Ltd , https://www.hikingfrp.com